Tags Posts tagged with "chevrolet"


2019-2020 Chevy Silverado 1500 TruPower by STILLEN Cold Air Intake Scoop - TP403501

STILLEN is excited to announce the much anticipated launch of the 2019 and up Chevy Silverado Cold Air Intake Scoop.  The team at STILLEN have created several videos showcasing the features and benefits of this true cold air intake scoop.  

2019-2020 Chevy Silverado 1500 TruPower by STILLEN Cold Air Intake Scoop - TP403501

The factory Air intake system on the Chevrolet Silverado 1500 is a very unique and creative design.  During testing our engineers placed multiple temperature probes throughout the engine bay and access panels of the Silverado engine bay in order to find the coldest possible air source. 

2019-2020 Chevy Silverado 1500 TruPower by STILLEN Cold Air Intake Scoop - TP403501

Turns out, Chevrolet engineers did a pretty good job of finding a great source of fresh air. Knowing that repositioning the air intake would not be beneficial our team of designers began looking at ways to improve the airflow and find additional benefits.

2019-2020 Chevy Silverado 1500 TruPower by STILLEN Cold Air Intake Scoop - TP403501

Pretty quickly our team noticed that the path of the airflow was good, but quite disruptive.  The air had to travel through the grille, up the radiator, through the lattice work of the shroud then around the radiator shroud and finally into the intake scoop.

This presented two problems.

1) There is no natural path for the air to flow through.

Every one of these turbulent areas, every interference causes restriction and/or causes work for the air.  The goal is to get the air into and through the air intake system as cleanly and efficiently as possible.

2) The air is susceptible to being heated by the radiator.

The air must travel up the face of the radiator in order to make its way into the air intake opening.  Keep in mind, the radiators operational temperature is 180-220 degrees….Significantly higher than ambient.  

2019-2020 Chevy Silverado 1500 TruPower by STILLEN Cold Air Intake Scoop - TP403501

To solve the two problems with this otherwise fantastic design the design team at STILLEN began by creating a proper scoop.  This scoop lowers the base of the radiator shroud to be in line with the top bar of the famous Chevrolet grille. This new design allows for the air to come directly into the intake system without being warmed by the radiator, or disrupted by the lattice type material in the radiator shroud.  This design eliminates the pre-heating and the turbulence caused by the factory system.

2019-2020 Chevy Silverado 1500 TruPower by STILLEN Cold Air Intake Scoop - TP403501

During our development our team noticed that the factory ¾ and 1 ton trucks actually have scoops in their radiator shroud designs also which confirmed that the TruPower by STILLEN cold air intake scoop for the Chevy Silverado was on the right track!

An additional benefit to this air intake is that it will work with any aftermarket air intake system that utilizes the factory air intake scoop.  

Features and Benefits:

  • Made in USA
  • Limited lifetime warranty
  • Direct cold air flow
  • Reduced intake air temperatures
  • Compatible with any air intake or supercharger that uses factory air intake scoop
  • Textured finish for OEM fit and finish
  • Very easy installation

2019-2020 Chevy Silverado 1500 TruPower by STILLEN Cold Air Intake Scoop - TP403501

STILLEN® is proud to announce the development of the Trupower by STILLEN cold air intake scoop for the 2019 Chevy Silverado.  Follow along as we let you in on all of the behind the scenes details that goes into developing this True cold air intake system to enhance the Chevy Silverado.

To start with the team began analyzing the 3D scanned CAD data to see how the factory air intake works.  By understanding how Chevrolet has engineered the factory system we are able to begin working on our concept for how to improve it.

We immediately saw that Chevy has developed a very unique air intake system from the factory that pulls air from the factory radiator covers to duct air into a tube that then goes in to the filter box.  The enters this tract by first traveling through the front grille area and then working its way up the radiator, through the lattice work material and the design of the hood and core support guides the air into the inlet tube.

Once we had a thorough understanding of this we began to look at ways to introduce even fresher, colder air into the system.  The team began mocking up some renderings in CAD until we had a few design ideas and were ready to bring in a vehicle for physical test fitment.

We always bring in a vehicle for physical test fitment before we proceed with building prototype parts because it is pretty common that the CAD data is missing a part, or some detail that you can only see once you have the subject vehicle in front of you.  This was the case again with the Chevy Silverado.  We immediately noticed that there were some support braces on the truck that were not present in the CAD data.

Additionally, with the vehicle in hand we are able to begin gathering engineering data from the vehicle.  We start by installing a series of sensors under the hood that allow us to monitor the temperature of the air in specific areas around the engine bay.  This way we can design our air intake system to bring in the coldest, freshest air possible.

With all of our engineering data, CAD models, and physical inspections completed we are able to begin building our prototypes.  Stay tuned for our next post and videos that walk through the product design and function in more detail.

2014-2019 Corvette C7 Stingray, Grand Sport, Z06 & ZR1 Body Styling By Street Scene Equipment

Street Scene is pleased to introduce their latest body styling products for the late model domestic sports car market with the 2014-2019 Chevy Corvette C7 Performance Body Styling Ground Effects Kit.

2014-2019 Corvette C7 Stingray, Grand Sport, Z06 & ZR1 Body Styling By Street Scene Equipment

This Street Scene Kit designed for the 2014-2019 Corvette C7 Stingray and Grand Sport offers an excellent value; with a simple installation you can truly transform the looks of your Corvette. Components of this kit can be purchased individually or as a whole.


2014-2019 Corvette C7 Stingray, Grand Sport, Z06 & ZR1 Body Styling By Street Scene Equipment

2014-2019 Corvette C7 Stingray and Grand Sport Ground Effects Kit. Transform your C7 with an aggressive functional design with the Street Scene C7 Corvette Ground Effects Kit. This Street Scene Kit designed for the Corvette C7 Stingray and Grand Sport offers an excellent value; with a simple installation you can truly transform the looks of your Corvette.


2014-2019 Corvette C7 Stingray, Grand Sport, Z06 & ZR1 Body Styling By Street Scene Equipment

2014-2019 Corvette C7 Front Splitter. Fits the 2014-2019 Corvette C7 Stingray and Grand Sport. Street Scene Equipment Polyurethane Front Splitter for the C7 Corvette adds great style and performance. Paired with the Street Scene Corvette C7 Side Skirts and Rear Corners to completely transform the look of your Corvette C7.


2014-2019 Corvette C7 Stingray, Grand Sport, Z06 & ZR1 Body Styling By Street Scene Equipment

2014-2019 Chevy Corvette C7 Side Skirts w/ Rear Corners. This Four Piece Kit includes Side Skirts (Side Splitters/Rockers) as well as the matching Rear Corner pieces. Designed to work with factory mounting locations for the 2014-2019 Corvette C7 Stingray and Grand Sport. Combine with Street Scene Corvette C7 Front Splitter for a complete ground effects kit for your C7 Corvette.


  • Aggressive race-inspired style and aero enhancement for your C7 Corvette
  • Polyurethane construction is both rigid enough to enhance aerodynamics while remaining durable enough for daily street use
  • Comes ready to paint or paintable finish
  • Easy installation using factory mounting locations
  • Designed, Engineered and Manufactured in Costa Mesa, CA USA




Featured Presentation:


Ready to add a stylish Body Kit to your 2014-19 Chevy C7 Corvette? Reach out to us at 866-250-5542, by email at sales@stillen.com or via live chat at stillen.com! Demand for these products are unprecedented, so order yours Today!

TOP Exhaust: Magnaflow 2016-2018 Camaro SS Exhaust System

TOP Exhaust: Magnaflow 2016-2018 Camaro SS Exhaust System 2016_CHEVY_CAMARO_SS_RED

Add Growl and Bark to the Camaro SS with Magnaflow Exhaust Solutions

The 2016+ Chevrolet Camaro SS enjoys the benefit of its 6.2L LT1 engine producing 455 horsepower and 455 lb-ft torque, all in a chassis that is 200 lbs. lighter than the previous model. But, as with most factory vehicles, the ferocity is muffled and sometimes even muzzled. This TOP Exhaust: Magnaflow 2016-2018 Camaro SS Exhaust System is one of the variables that can be upgraded to unleash the fury of the V8.

TOP Exhaust: Magnaflow 2016-2018 Camaro SS Exhaust System 19265

Magnaflow’s Cat-back Competition Exhaust (p/n 19339) features an X-pipe and dual twin-tip mufflers. This stainless-steel exhaust features 4-inch piping.

MagnaFlow released three variants of its stainless-steel Camaro exhaust solution. While each system helps to reduce weight, each accomplishes a different objective. The Magnaflow Dual Axle-back Competition Exhaust for 2016-2017 Chevrolet Camaro 6.2L (19339) features 3-inch piping, retains the factory B-pipes and replaces the factory muffler sections with MagnaFlow’s proprietary design. This offers a more aggressive tone without replacing the B-piping. The Magnaflow Quad Cat-Back Competition Exhaust for 2016-2017 Chevrolet Camaro 6.2L (19265) includes an X-pipe and axle-back mufflers manufactured from 4-inch piping. This system reduces back pressure and offers an X-pipe configuration feeding into the axle-back muffler sections. This X-pipe helps to balance the exhaust pulses between the left and right cylinder banks to ensure a steady and uniform exhaust flow.  The Magnaflow Dual Axle-Back Race Exhaust for 2016-2017 Chevrolet Camaro 6.2L (19338) eliminates the mufflers altogether and replaces them with polished 3-inch piping that connect to the factory B-pipes that terminate with 4-inch polished exhaust tips.

TOP Exhaust: Magnaflow 2016-2018 Camaro SS Exhaust System 19338

The Magnaflow Axle-back Race exhaust (p/n 19338) features 3-inch mandrel bent stainless-steel piping that terminate with a pair of polished 4-inch exhaust tips.


MagnaFlow Exhausts enjoy a host of features and benefits, including:

  • Limited Lifetime warranty against manufacturing defects
  • Dyno tested products proven to make power
  • Performance gains in both horsepower and torque
  • Competition Series: Aggressive Exhaust Note, Reduced System Mass
  • Race Series: Most Aggressive Exhaust Tone, Muffler-less Design
  • Easy to Install, Mandrel Bent Piping
  • Stainless-steel Construction that is Built to Last

Check out Magnaflow’s full line of exhausts at stillen.com!

For more information about the TOP Exhaust: Magnaflow 2016-2018 Camaro SS Exhaust System, or to place an order today:
Chat with us (866) 250-5542
Email sales@stillen.com
or Via live chat at stillen.com

K&N  Uncovers More Horsepower from the 2016 Camaro SS 6.2L

KN Camaro Intake Clipped


Chevrolet’s Generation V 6.2-liter small block V8 provides the 2016 Camaro SS with immense performance and surprising efficiency. The push rod, two valve-per-cylinder LT1 V8 generates 455 horsepower. It is similar to the LS family of small-block engines but features a unique aluminum block casting and cylinder heads, oiling system and an aggressive 11.5:1 compression ratio. It also incorporates advanced technologies such as direct fuel Injection and continuously variable valve timing.



An entirely new intake manifold design was developed to provide a straighter path into the combustion chamber. Although GM engineers invested in the development of the LT1 there is still room for improvement. K&N developed its AirCharger air intake system (p/n) 69-4534TP  for the SS to significantly improve incoming air flow as well as reduce turbulence in the intake tube. This intake has been chassis dyno-tested to deliver an estimated 15.16 horsepower gain over stock and can be installed in 90 minutes or less with simple hand tools. In addition to more power, this air intake system improves engine sound with a more aggressive and deeper tone during acceleration.

The air intake includes a chrome capped K&N high-flow air filter within a heat shield that replaces the original airbox space. The oversized conical air filter is manufactured from multiple layers of oiled cotton filter media, which offers less resistance than traditional paper filters. Air then passes through an aerodynamically-verified polished aluminum intake tube into the engine’s throttle body. The intake tube includes fittings for the factory mass air flow sensor and crank case vent hose.

KN Camaro Intake Installed

The only maintenance is a service you can do yourself at intervals of 100,000 miles (depending upon your driving conditions) using the K&N 99-5000 recharger kit to clean and refresh your air filter in preparation for another 100,000 miles of driving. This filter is designed to last for the lifetime of your vehicle, which K&N guarantees will perform for up to 10 years or 1,000,000 miles without requiring replacement.

The K&N 69-4534TP cold air intake is designed for both the 2016 and 2017 Chevrolet Camaro SS 6.2-liter V8.


STILLEN Product Announcement: Street Legal Edelbrock E-Force Supercharger Kits


50 State Street-Legal Boost by Edelbrock

The term “street legal” applies to cars that roll off the dealership’s lot or showroom floor. For the enthusiast seeking more performance, maintaining street-legal status requires the installation of government sanctioned upgrades. The state with the most stringent requirements in the nation is California, as set forth by the California Air Research Board (C.A.R.B.).


Scion FR-S / Subaru BRZ / Toyota 86 Supercharger Kit

If a manufacturer wishes to sell parts that have any effect on the emissions of a vehicle, it must submit its products to C.A.R.B. for evaluation to determine whether a product alters or modifies the design or performance of the factory emissions control systems. Once the design satisfies C.A.R.B. requirements, CARB will issue that specific product and vehicle application an Executive Order (E.O.) number for an exemption from the vehicle code, indicating that the part(s) or upgrades do not affect emissions and therefore may be used for street use. This is especially important in states that require emissions, where a visual inspection will fail if the parts installed are not street legal.


Camaro SS Supercharger kit (2010-13 Kit #1598 Shown)

Edelbrock has submitted numerous products to C.A.R.B. to be evaluated for a CARB EXEMPT Executive Order to allow street-legal use. Its latest E-Force Supercharger Systems for the 2016 Chevrolet Camaro SS, 2015-16 Corvette Z06, 2012-16 Jeep Wrangler and 2012-16 Scion FR-S, Subaru BRZ and Toyota GT86 have all received E.O. numbers, allowing more horsepower to be made legally.



Part Numbers                       E.O.#              Applications

1558, 1559, 15580, 15590  D-215-92       2016 Chevrolet Camaro SS

15731, 157310, 157320      D-215-90       2015-16 Chevrolet Corvette Z06

1527, 15270                          D-215-91       2012-2016 Jeep Wrangler

1556,15560                           D-215-93       2012-2016 Scion FR-S, Subaru BRZ, Toyota GT86


Jeep Wrangler Supercharger Kit

For more information about Edelbrock E-Force Supercharger solutions or to purchase an E-Force Supercharger kit for your ride, contact STILLEN at 866-250-5542, by email at sales@stillen.com or via Live Chat at stillen.com.

Most people immediately associate STILLEN with everything Nissan, while we do pride ourselves on our extensive knowledge of the name plate that was the corner stone of our founder Steve Millen’s racing career. We also, pride ourselves in our knowledge of just about every other make and model as well. We treat every car that comes into our performance center with extreme care and respect. From routine oil changes, to motor swaps, to brake jobs, there is never a corner cut or a shortcut taken in the work we do for our customer vehicles.  We are glad to see that word of this commitment to quality is spreading faster than ever,  a quick snapshot of the vehicles in our Performance Center today further illustrates this.

This customer is blending the line between street and track with an amazing suspension set up and a front and rear set of AP RACING brakes for his Subaru WRX STI



sti ap racing brakes


A different customer brought in his 2012 Chevrolet Camaro to get a Cat-back exhaust system installed in order to unleash the power and the sounds of his 6.2L  L99 Camaro SS.



We have a beautiful Nismo 350z in the corner of our shop getting a tune up and a Stage 3 Supercharger installed.


On our alignment rack we have a 2011 GT-R getting some angle dialed into it’s suspension in order to make it handle even better on the street and track.





News Release
For Immediate Release

FOR 2000-2010 GM 2500/3500 TRUCKS

Costa Mesa, Calif.– STILLEN announces the availability of a new front and rear big brake system for the 2000-2010 Chevrolet Silverado 2500/3500 and GMC Sierra 2500/3500 (including Dual Rear Wheel models). This rugged, state-of-the-art brake upgrade is based on AP Racing brake technology, the number one choice for a wide range of professional race teams that compete at the highest levels (i.e. NASCAR, FORMULA 1).

Available from the STILLEN brake product division, these GM Truck brake upgrades are compatible with OE ABS, traction control and stability systems as well as the original master cylinder to provide the ultimate in towing and big load capacity.

The front Big Brake System (AP2320) features AP Racing’s new, oversized 6-piston Heavy Duty caliper (CP8510) matched with the largest available aftermarket (16.1” diameter) 2-piece floating cross-drilled and slotted rotors. Slotted-only rotors are a no-cost option. This STILLEN brake system also includes high-performance Ferodo DS2500 brake pads along with Goodridge stainless steel brake lines, brackets and all necessary mounting hardware for immediate bolt-on.

For the matching and balanced rear Big Brake system (AP6950), STILLEN specified a special version of AP Racing’s Heavy Duty 4-piston caliper (CP5328) clamping on 15″ diameter 2-piece cross-drilled and slotted rotors, also available in slotted-only. The rear upgrade also includes Ferodo DS2500 brake pads and all necessary hardware.

This powerful brake system requires 20” or larger wheels with adequate spoke clearance. To ensure proper fitment, customers should visit www.stillen.com to download an easy-to-use brake profile template to check wheel fitment for both the front and rear brake kits before ordering. When ordering custom wheels, consult with STILLEN in advance to ensure compatibility.

To learn more about AP Racing Big Brake upgrade kits for the 2000-2010 Chevrolet Silverado 2500/3500 and GMC Sierra 2500/3500 and other pickup trucks, visit www.stillen.com, e-mail pr@stillen.com , or call (866) 250-5542.

# # #

Developed by enthusiasts for enthusiasts, STILLEN is a manufacturer and distributor of premium high performance products for late model import and domestic vehicles. Founded in 1986 by renowned professional driver and race car builder Steve Millen, STILLEN incorporates cutting-edge race proven technology and advanced aerodynamic designs into the company’s proprietary performance and appearance product lines. Millen is known worldwide for achieving the greatest number of wins in IMSA GT history during the course of an impressive 30-year racing career. Family owned and operated, STILLEN branded products include exhaust systems and components, superchargers, fuel systems and components, brake kits and components and urethane body styling products. In addition, STILLEN is an online reseller of many high performance products for late model cars and trucks, import and domestic, and creator of unique, one-of-a-kind performance project vehicles. For more information, visit www.STILLEN.com.